DNS Issues , cause’ its hard!!!

Resolving Domains Internally And Externally With Bind9 And Caching Nameserver

 

1.  Installing caching nameserver/ BIND 9:

Simplest method to install all required packages for this howto is,

$ yum install caching-nameserver bind*

same for apt based system, but if you don’t have yum or apt configured you can install following packages from your distribution cds, I am not mentioning package versions as it depends on your distribution i.e.

Required Packages: bind , bind-chroot, bind-utils, bind-lib, caching-nameserver

After installation of these packages we have to find either we have all required packges installed or not, to do so, use following command.

$ rpm -qa bind*

$ rpm -qa caching-nameserver

The above commands work fine, only if you are working on RPM based Linux Distro, otherwise check according to your own distro method. Now if you are able to see all mentioned packges , this means you are about to hit your nameserver with BIND hammer. 🙂

 

2.  Editing named.conf:

First of all we have to register our domain name with BIND, for the reason, we will edit named.conf, open it and type the following lines.

$ vi /etc/named.conf

Now type the following lines, i.e.

zone “cbtcandy.org” IN {
type master;
file “cbtcandy.org.zone”;
allow-update { none; };
};

You should replace cbtcandy.org with your own domain name.

 

3.  Starting Bind Daemon:

You can start bind daemon/service to check whether your named.conf is written perfectly, now you can do this by different method, I will state two of them:

For RedHat, CentOS, Fedora type systems, give following command,

$ service named start     <—- FEDORA

Now if Bind daemon is started successfully that means we are half way done.

 

4. Setting Bind Daemon Starts On Boot:

The following command will work perfectly on RedHat, CentOS, Fedora, but I am not sure about other distros, so better you find its equivalent.

$ chkconfig named on –level 35

 

5. Zone File Creation:

Now there is an issue. 😦 Where is my shotgun?

I.e. if you have installed bind-chroot, then you will be creating your domain zone file in /var/named/chroot/var/named/ directory, and then you will make a softlink to the /var/named/ directory, but if you didn’t install this chroot package, then you are going to create the zone file directly in the/var/named/ directory.

Now the following command works fine, if you have bind-chroot:

$ vi /var/named/chroot/var/named/cbtcandy.org.zone

OR   (if bind-chroot is not installed)

$ vi /var/named/cbtcandy.org.zone

and type the following lines into your zone file:

$TTL    86400
@               IN SOA  @ nayyares.gmail.com. (
42              ; serial (d. adams)
3H              ; refresh
15M             ; retry
1W              ; expiry
1D )            ; minimum
@               IN NS           nameserver.cbtcandy.org.
nameserver      IN A            192.168.1.1
cache           IN A            192.168.1.2
www             IN A            192.168.1.3
portal          IN A            192.168.1.4
You can add as many records as you wish 🙂 in this file.

Note: Here I am assuming that our DNS machine name is nameserver and LAN subnet is on 192.168.1.0/24 , you can change this according to your situation.

Now the following step is needed only if you have created the zone file in the /var/names/chroot/var/named/ directory.

$ ln -s /var/named/chroot/var/named/cbtcandy.org.zone /var/named/cbtcandy.org.zone

 

6.  Editing resolv.conf:

Now to tell our nameserver machine about the order it will look for name resolution, we have to edit /etc/resolv.conf file,

$ vi /etc/resolv.conf

and write the following two lines, but keep them in same order, as we want to first resolve domain resolution query by caching-name server, so we will keep 127.0.0.1 line first, in this file.

nameserver 127.0.0.1
nameserver 212.96.24.1

Note: I assume that your ISP’s nameserver machine IP is 212.96.24.1.

 

7.  Setting Up Host Name:

To set up your hostname according to your domain, we will edit /etc/sysconfig/network file, i.e.

$ vi /etc/sysconfig/network

Now type the following line:

HOSTNAME=nameserver.cbtcandy.org

 

8. Restarting BIND Daemon:

$ service named restart               (Redhat,Fedora,Centos)

OR

$ /etc/rc.d/rc.bind restart            (Suse,Debian)

 

9. Testing:

Now to test whether your configuration is working fine or not, give the following command:

$ nslookup nameserver.cbtcandy.org

If you get the following result, this means your BIND 9 is working fine:

Server:         127.0.0.1
Address:        127.0.0.1#53

Name:   nameserver.cbtcandy.org
Address: 192.168.1.1

Now to test your caching-nameserver, give the following command:

$ nslookup http://www.howtoforge.org

If you are getting the following result, this means the caching-nameserver is working fine.

Server:         212.96.24.1
Address:        212.96.24.1#53

Name:   http://www.howtoforge.org
Address: 85.10.207.148

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s